|
View Full Version : Power On/Off not working? HuskerHarley 03-14-2009, 12:23 PM I'm not able to power on TV with ControlCal. I have the cable bundle from CC, also port seems OK, I'm lost, I did a search but nothing really helped. HELP...:please: HH Turbe 03-14-2009, 12:28 PM Hi, :hiya: Did you verify ControlCAL's port setting (COM Port) is set to the one that the ControlCAL USB Adapter is configured to? Need to match up the COM Port and the Port Settings. What COM Port is the Adapter configured for (need to go into your Control Panel). What O/S are you using. Did you install the USB Serial Adapter's drivers before plugging the Adapter in your computer's USB Port? Do you have the 9G ISFccc Regions1 Display Profile loaded? Double check the cable connections including on back of your Elite. In ControlCAL's Terminal Window, when you press the POWER ON button on the Profile, do you see: <---- SENT ----> RECEIVED ? HuskerHarley 03-14-2009, 12:45 PM Hi, :hiya: Did you verify ControlCAL's port setting (COM Port) is set to the one that the ControlCAL USB Adapter is configured to? Need to match up the COM Port and the Port Settings. No What COM Port is the Adapter configured for (need to go into your Control Panel). I need to be talked/guided to find this. What O/S are you using. Did you install the USB Serial Adapter's drivers before plugging the Adapter in your computer's USB Port? XP, Do you have a link so I can reload them? Do you have the 9G ISFccc Regions1 Display Profile loaded? Double check the cable connections including on back of your Elite. Done that several times. In ControlCAL's Terminal Window, when you press the POWER ON button on the Profile, do you see: <---- SENT ----> RECEIVED Yes ? HH Turbe 03-14-2009, 12:50 PM There is a NOTE (titled IMPORTANT!) that comes with the Bundle. Did you toss it out? :( XP, Do you have a link so I can reload them? Did you download the drivers and install them in the first place? :confused: Most likely, you have ControlCAL set to the COM Port of your computer's internal modem. Unplug the adapter, Reboot and follow the instructions Here (http://www.controlcal.com/forum/showthread.php?t=176). HuskerHarley 03-14-2009, 01:10 PM There is a NOTE (titled IMPORTANT!) that comes with the Bundle. Did you toss it out? :( :oops: Did you download the drivers and install them in the first place? :confused: Yes, My computer shot craps and I had to re-download controlcal and I'm sure I messed things up Most likely, you have ControlCAL set to the COM Port of your computer's internal modem. Unplug the adapter, Reboot and follow the instructions Here (http://www.controlcal.com/forum/showthread.php?t=176). I'll do that. HH HuskerHarley 03-14-2009, 01:24 PM :thumbup::clap::thumbup: Thank You, I have been going insane for the last 5 hrs.,,,The drivers were missing and the link is perfect...Now I can get to work. :thumbsup:Turbe:thumbsup: HH HuskerHarley 03-14-2009, 01:36 PM Well I hope I didn't celebrate too early:confused: When I send a command/setting I'm getting "RECEIVED ERROR CODE" on every adjustment, should I be concerned? HH Turbe 03-14-2009, 01:41 PM You are now able to POWER ON/OFF the Display with the Buttons, right? If so, study these Threads (you need to read them before doing anything, then follow them step by step): Step-by-Step Instructions to activate an ISF Memory: http://www.controlcal.com/forum/showpost.php?p=2218&postcount=16 http://www.controlcal.com/forum/showpost.php?p=1436&postcount=3 . HuskerHarley 03-14-2009, 02:16 PM You are now able to POWER ON/OFF the Display with the Buttons, right? If so, study these Threads (you need to read them before doing anything, then follow them step by step): Step-by-Step Instructions to activate an ISF Memory: http://www.controlcal.com/forum/showpost.php?p=2218&postcount=16 http://www.controlcal.com/forum/showpost.php?p=1436&postcount=3 . I have read and do have copies in hand, from the time I did this in early February, for some reason after I started all over again this time (another reboot) it worked perfect, all green no red. Once again, Thank-U for your time and the invaluable information.:thumbup: HH ste_diver 04-19-2009, 10:21 AM Help Turbe, I tried to power on the TV <---- SENT ----> RECEIVED But the tv still renmain switched off. When I push the button stRT CAlibATE it appears the message Display isf is not compatble with.... and evan if I do the f12 procedure <---- CR HEX:OD ----> CR HEX:OD nothing happen. What i did wrong? Turbe 04-19-2009, 11:13 AM If you can't Power ON/OFF, don't bother trying START CALIBRATION. Looks like you may have ControlCAL set to the wrong COM Port since you are seeing ----> RECEIVED You may have it Set to a Modem. I just thought of something else, what does the Window's Title Bar say "PROFILE: Mitsubishi HC Series Projectors" ? What Display Model do you have? If you have a Pioneer, you want to open/load the Pioneer Display Profile for your Model in ControlCAL (MENU/FILE/OPEN) and use the POWER ON/OFF Buttons in that Display Profile. ControlCAL does have a Built-In Display Profile, which is the Mitsubishi one. This won't work on Pioneers. ste_diver 04-19-2009, 11:50 AM Thankyou Turbe I set correctly the com port from the control panel and now everithing work well |