Pro-101FD ISF Night/Day Settings

[sillysally]

Pioneer 9G Elite Monitor 101 ISF- Settings.


Picture Settings:
AV Selection: ISF-Night/Day
Contrast: 26
Brightness:0
Color: +2
Tint: 0
Sharpness: -15

Pure Cinema: 2 (Advance)
Black Level: 0 (Off)
CTI: 0 (Off)
Color Space: 2
Color Temp: 6 (Manual)
Screen size 0 (Dot By Dot)

ACL: 0 (Off)
3DYC: 2
I-P Mode: 2
Text Optimization: 0 (Off)
Intelligent Mode: 0 (Off)
DRE Picture: 0 (Off)

Enhancer Mode: 1
Block NR: 0 (Off)
3DNR: 0 (Off)
Field NR: 0 (Off)
Mosquito NR: 0 (Off)

Power Save Mode: Off
Orbiter: Mode 0

RGB Controls
R High:-4
G High: 0
B High:+3
R Low: -2
G Low: 0
B Low: -2

Color Management
R: 0
Y: 0
G: 0
C: 0
B: 0
M: 0

Gamma
10%R 0
10%G 0
10%B 0
20%R 0
20%G 0
20%B 0
30%R 0
30%G 0
30%B 0
40%R 0
40%G 0
40%B 0
50%R 0
50%G 0
50%B 0
60%R 0
60%G 0
60%B 0
70%R 0
70%G 0
70%B 0
80%R 0
80%G 0
80%B 0
90%R 0
90%G 0
90%B 0

Template by D-Nice

[ncfoster]

I know that I already posted this over on AVS, but thank you so much. I haven't tried the settings yet, but I've been waiting forever.

What playback device were you calibrating with your 101? Thanks.

[sillysally]

I know that I already posted this over on AVS, but thank you so much. I haven't tried the settings yet, but I've been waiting forever.

What playback device were you calibrating with your 101? Thanks.

You probably saw my reply on AVS.

I used a Pioneer BDP-05/51.

[ncfoster]

I did see it, but obviously it is a lot less cluttered here. :) I have a Panasonic BD-35. I believe you calibrated your 141 with one of these somewhere along the line. I believe that there was some variation in your settings from one player to the next (feel free to correct me if that is incorrect).

Over on AVS, you made the following statement:

I used a BDP-05/51 to do the ISF calibration. But because of how these BD players work, I felt that these settings could be ok to use with most input devises, as long as the source doesn't change the output signal.

I know that you've gone through a bunch of Blu-Ray players, and I would presume that you have settled on this one. Since proper calibration is off the table for me right now, do you think these settings are likely to be good for a BD-35? Any other advice on that front? Thanks much for the settings again.

[sillysally]

I did see it, but obviously it is a lot less cluttered here. :) I have a Panasonic BD-35. I believe you calibrated your 141 with one of these somewhere along the line. I believe that there was some variation in your settings from one player to the next (feel free to correct me if that is incorrect).

Over on AVS, you made the following statement:

I know that you've gone through a bunch of Blu-Ray players, and I would presume that you have settled on this one. Since proper calibration is off the table for me right now, do you think these settings are likely to be good for a BD-35? Any other advice on that front? Thanks much for the settings again.

Yes I do think your BD-35 will work with these setting. :thumbsup:

I used the BD-05/51 because it is a more main stream BD player than my BDP-09. And anyway us owners after the long road that we have been on waiting for Pioneer to upgrade the Firmware need a break. ;)

The BD player that I have settled on is my BDP-09. As long as Pioneer upgrades the firmware so it will decode DTS-HD. :please:

[ShoeHorn]

Turbe

Your PM box needs clearing:)

[Turbe]

Cleaned some, got several PM's last night..

[Djoss]

Does someone have day/night settings for a PS3?