View Single Post
Unread 10-07-2015, 11:44 AM   #16
ConnecTED
Junior Member
Registered Supporter
 
Join Date: Jun 2010
Location: Athens, Greece
Posts: 21
Thanks: 0
Thanked 1 Time in 1 Post
Default

CalMAN 5 Workflows Setup

The CalMAN 5 Workflows I have designed for the Ted's LightSpace CMS Calibration Disk Users require CalMAN 5 Enthousiast/Ultimate or Design Mode Add-On License to be able to open and use them.

For Ted's LightSpace CMS Calibration Disk users with CalMAN Basic or Control License (or other License level that can't open custom designed workflows), they can use the Quick Analysis Workflow to calibrate Color Gamut using 100% Saturation with 100% Stimulus Level / 100% Saturation with 75% Stimulus Level / 75% Saturation with 100% Stimulus Level / 75% Saturation with 75% Stimulus.

Some CalMAN license levels can use Quick Analysis Workflow to take Saturation/Luminance measurements runs to verify their calibrations using 4/5/10-Point Saturation with 75%/100% Stimulus Level or 4/5/10-Point Luminance with 75%/100% Stimulus Level.

To perform the measurements it's required some changes of CalMAN Settings, so I'm posting below the correct settings per measurement run:

About Quick Analysis Workflow using Ted's LightSpace CMS Calibration Disk:



For Color Gamut Calibration using 100% Saturation / 100% Stimulus Level: Go to ColorSpace layout page, Change the Stimulus Level to 100. About all other settings of the Layout page it doesn't matter where they are.

For Color Gamut Calibration using 100% Saturation / 75% Stimulus Level: Go to ColorSpace layout page, Change the Stimulus Level to 75. About all other settings of the Layout page it doesn't matter where they are.

For Color Gamut Calibration 75% Saturation / 100% Stimulus Level: Go to Saturation Sweeps layout page, Change the Stimulus Level to 100, Change Saturation Sweep to 75% only, About all other settings of the Layout page it doesn't matter where they are. Go to Workflow Advanced Options and un-tick the Saturation targets use constant luminance.

For Color Gamut Calibration 75% Saturation / 75% Stimulus Level: Go to Saturation Sweeps layout page, Change the Stimulus Level to 75, Change Saturation Sweep to 75% only, About all other settings of the Layout page it doesn't matter where they are. Go to Workflow Advanced Options and un-tick the Saturation targets use constant luminance.



Verify x-Point Saturation using Quick Analysis Workflow with Ted's LightSpace CMS Calibration Disk:

For 4-Point Saturation / 100% Stimulus Level: Go to Saturation Sweep layout page, Change the Stimulus Level to 100 and set Saturation Sweeps to 25% Sweeps. About all other settings of the Layout page it doesn't matter where they are. Go to Workflow Advanced Options and un-tick the Saturation targets use constant luminance.

For 4-Point Saturation / 75% Stimulus Level: Go to Saturation Sweep layout page, Change the Stimulus Level to 75 and set Saturation Sweeps to 25% Sweeps. About all other settings of the Layout page it doesn't matter where they are. Go to Workflow Advanced Options and un-tick the Saturation targets use constant luminance.

For 5-Point Saturation / 100% Stimulus Level: Go to Saturation Sweep layout page, Change the Stimulus Level to 100 and set Saturation Sweeps to 20% Sweeps. About all other settings of the Layout page it doesn't matter where they are. Go to Workflow Advanced Options and un-tick the Saturation targets use constant luminance.

For 5-Point Saturation / 75% Stimulus Level: Go to Saturation Sweep layout page, Change the Stimulus Level to 75 and set Saturation Sweeps to 20% Sweeps. About all other settings of the Layout page it doesn't matter where they are. Go to Workflow Advanced Options and un-tick the Saturation targets use constant luminance.

For 10-Point Saturation / 100% Stimulus Level: Go to Saturation Sweep layout page, Change the Stimulus Level to 100 and set Saturation Sweeps to 10% Sweeps. About all other settings of the Layout page it doesn't matter where they are. Go to Workflow Advanced Options and un-tick the Saturation targets use constant luminance.

For 10-Point Saturation / 75% Stimulus Level: Go to Saturation Sweep layout page, Change the Stimulus Level to 75 and set Saturation Sweeps to 10% Sweeps. About all other settings of the Layout page it doesn't matter where they are. Go to Workflow Advanced Options and un-tick the Saturation targets use constant luminance.

Verify x-Point Luminance using Quick Analysis Workflow with Ted's LightSpace CMS Calibration Disk:

For 4-Point Luminance / 100% Stimulus Level: Go to Luminance Sweep layout page, Change the Stimulus Level to 100 and set Gamut Ramp Points to 4-Point 25% Step 25-100%. About all other settings of the Layout page it doesn't matter where they are. (Workflow Advanced Options - saturation targets use constant luminance...doesn't matter if ticked or unticked.)

For 4-Point Luminance / 75% Stimulus Level: Go to Luminance Sweep layout page, Change the Stimulus Level to 75 and set Gamut Ramp Points to 4-Point 25% Step 25-100%. About all other settings of the Layout page it doesn't matter where they are. (Workflow Advanced Options - saturation targets use constant luminance...doesn't matter if ticked or unticked.)

For 5-Point Luminance / 100% Stimulus Level: Go to Luminance Sweep layout page, Change the Stimulus Level to 100 and set Gamut Ramp Points to 5-Point 20% Step 20-100%. About all other settings of the Layout page it doesn't matter where they are. (Workflow Advanced Options - saturation targets use constant luminance...doesn't matter if ticked or unticked.)

For 5-Point Luminance / 75% Stimulus Level: Go to Luminance Sweep layout page, Change the Stimulus Level to 75 and set Gamut Ramp Points to 5-Point 20% Step 20-100%. About all other settings of the Layout page it doesn't matter where they are. (Workflow Advanced Options - saturation targets use constant luminance...doesn't matter if ticked or unticked.)

For 10-Point Luminance / 100% Stimulus Level: Go to Luminance Sweep layout page, Change the Stimulus Level to 100 and set Gamut Ramp Points to 10-Point 10% Step 10-100%. About all other settings of the Layout page it doesn't matter where they are. (Workflow Advanced Options - saturation targets use constant luminance...doesn't matter if ticked or unticked.)

For 10-Point Luminance / 75% Stimulus Level: Go to Luminance Sweep layout page, Change the Stimulus Level to 75 and set Gamut Ramp Points to 10-Point 10% Step 10-100%. About all other settings of the Layout page it doesn't matter where they are. (Workflow Advanced Options - saturation targets use constant luminance...doesn't matter if ticked or unticked.)

Tip For CalMAN 5 Users that will use Ted's CalMAN 5 Workflows with Pattern Generators



For the users that are using the Ted's CalMAN 5 Workflows, as you noticed, there is not available at any layout page the ReadAll button, since all workflow have been configured to work with Singe Read with AutoAdvance.

For the users that can use the CalMAN Workflow Design feature, there is no need to enter to design mode to add manually a ReadAll button, they can use the CalMAN's Keyboard Shortcut for that.

Before that, the users have to enable the Keyboard Shortcuts feature from CalMAN's Application Preferences and after than they can simply press F10 key which is the keyboard shortcut key for ReadAll at any CalMAN layout page.



This is helpful for users that are using Ted's CalMAN Workflows with External Hardware Pattern Generators or with CalMAN's Internal Pattern Generator.

CalMAN 5 Tip for faster Start-Up

CalMAN 5 can load faster, for about 5-6 seconds if you remove all unused workflows from the CalMAN's Workflow folder which is located (C:\Users\*User Name*\Documents\SpectraCal\CalMAN 5 for Business\Workflows) and keepe in that directory only the workflows you usually using or those can opened by your CalMAN license level.
ConnecTED is online now   Reply With Quote