Calibration Forums
 
 

Go Back   Calibration Forums > DIY Calibration - Display Devices > Flat Panels - Plasma > Pioneer > Pioneer User Posted Settings

Notices
Old 09-14-2008, 08:35 PM   #1
D-Nice
Senior Member
 
Join Date: Jul 2008
Posts: 171
Thanks: 0
Thanked 349 Times in 55 Posts
Default PRO-111FD Pure Mode Settings

Pioneer 111FD Pure Mode Settings

Picture:
AV Selection: Pure
Contrast: 37
Brightness: 0
Color: +3
Tint: 0
Sharpness: -15


Pro Adjust

Pure Cinema
Film Mode: Advance
Text Optimization: Off

Intelligence: Off


Picture Detail:
DRE Picture: Off
Black Level: Off
ACL: Off
Enhancer Mode: 1
Gamma: 2


Color Detail:
Color Temp: Manual
R High -1
G High 0
B High +4
R Low -1
G Low +1
B Low 0

CTI: Off

Color Management
R -2
Y +2
G -1
C -1
B +1
M -1

Color Space: 2


Noise Reduction:

3DNR: Off
Field NR: Off
Block NR: Off
Mosquito NR: Off

Screen Size: Full
Power Save Mode: Off
Orbiter: Mode 2


Calibration Report:
Can't view the Reports? Register to view attachments. It's free!

Last edited by D-Nice; 11-23-2008 at 03:29 PM.
D-Nice is offline   Reply With Quote
Sponsored Links
Register to remove these ads. It's free!



Register to remove these ads. It's free!
Old 10-23-2008, 11:07 AM   #2
PioFreak
Junior Member
Registered Supporter
 
Join Date: Sep 2008
Posts: 28
Thanks: 0
Thanked 1 Time in 1 Post
Default

I thought you said a rule of thumb was not to mess with Green high or green low. Also I thought that anything above 2 clicks either way in the CMS messed with the grayscale. But the calibration report looks amazing! Did you find something new out?
__________________
5090
PioFreak is offline   Reply With Quote
Old 10-24-2008, 06:50 AM   #3
D-Nice
Senior Member
 
Join Date: Jul 2008
Posts: 171
Thanks: 0
Thanked 349 Times in 55 Posts
Default

Quote:
Originally Posted by PioFreak View Post
I thought you said a rule of thumb was not to mess with Green high or green low. Also I thought that anything above 2 clicks either way in the CMS messed with the grayscale. But the calibration report looks amazing! Did you find something new out?
That rule of thumb still stands....and I've updated those settings as they were old anyway
D-Nice is offline   Reply With Quote
Old 10-24-2008, 08:43 AM   #4
PioFreak
Junior Member
Registered Supporter
 
Join Date: Sep 2008
Posts: 28
Thanks: 0
Thanked 1 Time in 1 Post
Default

By the way, thanks for your contributions and sharing of knowledge. It means a lot, especially to those of us starting out in calibration as DIY'ers for fun. Your settings are really the best that I have found on the internet and work spot on for my 5090. That proves to me there is a fundamental similarity between the NA elites and the 5090. These settings are clearly superior for me even compared to the 5090 settings floating around...go figure.

I changed a few little things ....like red high to -4 and Blue high to +2, and contrast to 38. Just "by eye" preferences until I get the 1ipro and Calman. But that may change because my bias backlight was about 5200k before, but I just installed a GAM color filter over them to pull up the color temp closer to 6500k and also reduce the light output. The filter also reduces luminosity by .5 stops. So maybe a the settings will change in some small way tonite.

Thanks again.
__________________
5090
PioFreak is offline   Reply With Quote
Old 01-19-2009, 05:09 AM   #5
abax2000
Junior Member
 
Join Date: Jan 2009
Posts: 4
Thanks: 0
Thanked 0 Times in 0 Posts
Default KRP-500A Pure mode

Are these settings valid for KRP-500A Pure Mode?
If not, do you know where can I look for them?
abax2000 is offline   Reply With Quote
Old 01-19-2009, 10:56 AM   #6
Turbe
Senior Member
Professional Supporter
 
Turbe's Avatar
 
Join Date: Apr 2008
Posts: 1,919
Thanks: 194
Thanked 179 Times in 138 Posts
Default

Quote:
Originally Posted by abax2000 View Post
Are these settings valid for KRP-500A Pure Mode?
If not, do you know where can I look for them?
No, but a Member has posted ISFccc Settings (not Pure) for the KRP-A's here: http://www.controlcal.com/forum/showthread.php?t=139

ControlCAL is used to access, activate and adjust your Display's ISFccc Interface (isf Night, isf Day, isf Auto).

Many like to use settings Posted by others but please do consider doing a proper Calibration (DIY is fine) by using a meter (Chroma 5 or I1 Pro) and additional software.....
Turbe is offline   Reply With Quote
Old 01-21-2009, 11:45 PM   #7
abax2000
Junior Member
 
Join Date: Jan 2009
Posts: 4
Thanks: 0
Thanked 0 Times in 0 Posts
Default

thnx
Just needed a starting point and a cross reference and can't find one.
abax2000 is offline   Reply With Quote
Reply

Bookmarks

Tags
d-nice, isfccc, pioneer, pioneer 9g, pioneer elite, plasma, pro-111fd, pro-151fd

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Sponsored Links


All times are GMT -7. The time now is 05:22 AM.


Powered by vBulletin® Version 3.7.5
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Advertisement System V2.3 By   Branden
©2008 - 2018 ControlCAL.com