Calibration Forums
 
 

Go Back   Calibration Forums > DIY Calibration - Display Devices > Flat Panels - Plasma > Pioneer

Notices
Old 12-30-2009, 07:38 PM   #21
jebj
Junior Member
Professional Supporter
 
Join Date: Feb 2009
Posts: 13
Thanks: 0
Thanked 12 Times in 5 Posts
Default

Here is an update that includes ISF-Night Mode

Picture
AV Selection: Pure
Contrast : 37
Brightness : 1
Color : 4
Tint : 0
Sharpness : -12
Color Temp : Manual
Red High : -7
Green High : 0
Blue High : -2
Red Low : 0
Green Low : 2
Blue Low : 3
Gamma : 2

Pure Cinema
Film Mode : Advance
Text Optimization: Off

Intelligent Mode: Off

Picture Detail
DRE Picture : Off
Black Level : Off
ACL : Off
Enhancer Mode: Hard

Color Detail
CTI: Off
Color Management
R (RED) : 0
Y (YELLOW) : 0
G (GREEN) : 0
C (CYAN) : 0
B (BLUE) : 0
M (MAGENTA): 0
Color Space : 2

Noise Reduction
3DNR : Off
Field NR : Off
Block NR : Off
Mosquito NR: Off

Other
3DYC : Middle
IP Mode : 2 (Standard)
Drive Mode : 1 (75Hz)
Game Control : Off
Blue Only Mode: Off

Power & Options
Energy Save Mode : Standard
Room Light Sensor: Off


Picture
AV Selection: ISF-Night
Contrast : 25
Brightness : 1
Color : 4
Tint : 0
Sharpness : -12
Color Temp : Manual
Red High : -7
Green High : 2
Blue High : 0
Red Low : 1
Green Low : 2
Blue Low : 2
Gamma : 3 (ISF 9 Point Gamma in use)
ISF Gamma 1 2 3 4 5 6 7 8 9
Red : -1 -1 -1 -1 -1 -1 -1 -1 -1
Green : -1 -1 -1 -1 -1 -1 -1 -1 -1
Blue : -1 -1 -1 -1 -1 -1 -1 -1 -1
ISF Gamma 123456789
Red -1-1-1-1-1-1-1-1-1
Green -1-1-1-1-1-1-1-1-1
Blue -1-1-1-1-1-1-1-1-1

Pure Cinema
Film Mode : Advance
Text Optimization: Off

Intelligent Mode: Off

Picture Detail
DRE Picture : Off
Black Level : Off
ACL : Off
Enhancer Mode: Hard

Color Detail
CTI: Off
Color Management
R (RED) : 0
Y (YELLOW) : 0
G (GREEN) : 0
C (CYAN) : 0
B (BLUE) : 0
M (MAGENTA): 0
Color Space : 2

Noise Reduction
3DNR : Off
Field NR : Off
Block NR : Off
Mosquito NR: Off

Other
3DYC : Middle
IP Mode : 2 (Standard)
Drive Mode : 1 (75Hz)
Game Control : Off
Blue Only Mode: Off

Power & Options
Energy Save Mode : Standard
Room Light Sensor: Off


Picture
AV Selection: ISF-Day
Contrast : 34
Brightness : 1
Color : 4
Tint : 0
Sharpness : -12
Color Temp : Manual
Red High : -7
Green High : 2
Blue High : 0
Red Low : 1
Green Low : 2
Blue Low : 2
Gamma : 3 (ISF 9 Point Gamma in use)
ISF Gamma 1 2 3 4 5 6 7 8 9
Red : -1 -1 -1 -1 -1 -1 -1 -1 -1
Green : -1 -1 -1 -1 -1 -1 -1 -1 -1
Blue : -1 -1 -1 -1 -1 -1 -1 -1 -1
ISF Gamma 123456789
Red -1-1-1-1-1-1-1-1-1
Green -1-1-1-1-1-1-1-1-1
Blue -1-1-1-1-1-1-1-1-1

Pure Cinema
Film Mode : Advance
Text Optimization: Off

Intelligent Mode: Off

Picture Detail
DRE Picture : Off
Black Level : Off
ACL : Off
Enhancer Mode: Hard

Color Detail
CTI: Off
Color Management
R (RED) : 0
Y (YELLOW) : 0
G (GREEN) : 0
C (CYAN) : 0
B (BLUE) : 0
M (MAGENTA): 0
Color Space : 2

Noise Reduction
3DNR : Off
Field NR : Off
Block NR : Off
Mosquito NR: Off

Other
3DYC : Middle
IP Mode : 2 (Standard)
Drive Mode : 1 (75Hz)
Game Control : Off
Blue Only Mode: Off

Power & Options
Energy Save Mode : Standard
Room Light Sensor: Off
Attached Files
File Type: pdf Pure.pdf (164.0 KB, 64 views)
File Type: pdf ISF-Night.pdf (165.3 KB, 47 views)
File Type: pdf ISF-Day.pdf (165.8 KB, 59 views)
jebj is offline   Reply With Quote
The Following 2 Users Say Thank You to jebj For This Useful Post:
Sponsored Links
Register to remove these ads. It's free!



Register to remove these ads. It's free!
Old 12-30-2009, 10:08 PM   #22
MacHound
Junior Member
 
Join Date: Dec 2009
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Thanks, JebJ. Those settings will come in handy when I receive my PRO-101FD next week.
MacHound is offline   Reply With Quote
Old 12-31-2009, 10:06 AM   #23
Turbe
Senior Member
Professional Supporter
 
Turbe's Avatar
 
Join Date: Apr 2008
Posts: 1,921
Thanks: 194
Thanked 179 Times in 138 Posts
Default

jebj has his own Thread now in the User Posted Settings Area..

http://www.controlcal.com/forum/showthread.php?t=544

Turbe is offline   Reply With Quote
Old 01-22-2010, 10:15 PM   #24
azmodien
Junior Member
Registered Supporter
 
Join Date: Jan 2010
Posts: 7
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Quote:
Originally Posted by Turbe View Post
D-Nice now has a PRO-101FD in his collection and he said that he will have settings posted soon....

Stay Tuned
Has D-Nice posted his settings for the 101FD? I haven't seen them in any other threads.
azmodien is offline   Reply With Quote
Old 04-09-2010, 04:06 PM   #25
Loop
Junior Member
Registered Supporter
 
Join Date: Apr 2010
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Quote:
Originally Posted by azmodien View Post
Has D-Nice posted his settings for the 101FD? I haven't seen them in any other threads.
I don't think he ever posted them, even on the AVS Forum break in thread he has post break in settings for all the sets but the 101
Loop is offline   Reply With Quote
Old 04-19-2010, 09:39 PM   #26
Floridaman
Junior Member
 
Join Date: Apr 2010
Posts: 6
Thanks: 0
Thanked 2 Times in 2 Posts
Default Question about ISF Day/Night mode

I just had inputs 5 and 6 calibrated and isf day and night activated on my Pioneer Elite Pro-101FD. Once the ISF day and night mode is activated and calibrated do the settings have to be applied to each resolution setting of 480i, 480p, 720p etc? The reason I ask this is all of the other modes like pure have to be set by input and signal. Meaning 720p and 1080i have to be set individually of each other. I would think that once the ISF modes are set and locked it would apply to all of the resolutions.
Floridaman is offline   Reply With Quote
The Following User Says Thank You to Floridaman For This Useful Post:
Old 04-19-2010, 10:07 PM   #27
Turbe
Senior Member
Professional Supporter
 
Turbe's Avatar
 
Join Date: Apr 2008
Posts: 1,921
Thanks: 194
Thanked 179 Times in 138 Posts
Default

Hi,

ISFccc memories apply to all Resolutions/Signals on that Input.
Turbe is offline   Reply With Quote
Old 04-20-2010, 05:40 AM   #28
Floridaman
Junior Member
 
Join Date: Apr 2010
Posts: 6
Thanks: 0
Thanked 2 Times in 2 Posts
Default

Thanks for the reply. I figured it applied to all resolutions but just wanted to double check.
Floridaman is offline   Reply With Quote
Old 04-20-2010, 08:32 PM   #29
Floridaman
Junior Member
 
Join Date: Apr 2010
Posts: 6
Thanks: 0
Thanked 2 Times in 2 Posts
Default

Turbe:

Is it correct to say that Control Cal is used to activate ISF modes and for entering the settings and doesn't do the actual calibrating? I had my set professionally calibrated and they used Control Cal for opening the ISF modes and for the settings. The calibration was done with Colorfacts Pro for the measurements. Is this a good piece of software for the calibrating?

Thanks
Floridaman is offline   Reply With Quote
Old 04-20-2010, 09:15 PM   #30
Turbe
Senior Member
Professional Supporter
 
Turbe's Avatar
 
Join Date: Apr 2008
Posts: 1,921
Thanks: 194
Thanked 179 Times in 138 Posts
Default



ControlCAL is used with Calibration Software (like Colorfacts, CalMAN etc). ControlCAL 'talks' to the display, the Calibration Software 'talks' to the meter and optionally to the pattern sources.

Colorfacts has been discontinued (long ago), there are Calibrators using it still but many have moved to CalMAN which supports doing gamut work (without external calculations) and supports more meters and pattern sources than any other Calibration Software (past or present). Another reason many have moved to CalMAN is for its reporting options.

Last edited by Turbe; 04-20-2010 at 09:49 PM.
Turbe is offline   Reply With Quote
Old 04-20-2010, 09:35 PM   #31
Floridaman
Junior Member
 
Join Date: Apr 2010
Posts: 6
Thanks: 0
Thanked 2 Times in 2 Posts
Default

Thanks for the quick response. Since Colorfacts was used by the calibrator does that mean I didn't get as accurate of a calibration that I would have gotten with Calman?
Floridaman is offline   Reply With Quote
Old 04-20-2010, 09:48 PM   #32
Turbe
Senior Member
Professional Supporter
 
Turbe's Avatar
 
Join Date: Apr 2008
Posts: 1,921
Thanks: 194
Thanked 179 Times in 138 Posts
Default

No, that is not what I was trying to say, though when it comes to accuracy, CalMAN is currently King

Quote:
Sitting under the hood of CalMAN is our exclusive Calibration Optimization and Reporting Environment (CORE) engine. Written exclusively using 64-bit double-precision floating point math, the CORE engine outperforms even popular spreadsheet applications for calculation accuracy because it never has to drop to single-precision or integer operations for convenience or speed purposes.

The CORE engine also includes advanced matrix operations and statistical techniques so that CalMAN users do not suffer from errors and inaccuracies caused by unnecessary rounding of critical input variables or by the use of inappropriate or inefficient estimation models. CalMAN typically uses >12 decimal places for key variables like XYZ-to-RGB matrices, where previously users might have been limited to four or fewer. Wherever possible, the CORE engine computes such critical values, rather than relying on outside files or tables.
Turbe is offline   Reply With Quote
Old 02-13-2017, 02:33 PM   #33
PaulDieter
Junior Member
 
Join Date: Feb 2017
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
Default Pioneer 101fd

Is there anyone still on here to talk about the pioneer 101fd?
PaulDieter is offline   Reply With Quote
Old 02-14-2017, 02:29 PM   #34
DisplayHarmony
Member
Charter Supporter
 
Join Date: Jul 2008
Posts: 77
Thanks: 3
Thanked 15 Times in 9 Posts
Default

around yes but it can be slow around here
DisplayHarmony is offline   Reply With Quote
Reply

Bookmarks

Tags
101fd, calibration, isf, isfccc, isfccc settings, pioneer, pro-101fd, settings

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Sponsored Links


All times are GMT -7. The time now is 03:05 PM.


Powered by vBulletin® Version 3.7.5
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Advertisement System V2.3 By   Branden
©2008 - 2018 ControlCAL.com